WIRELESS SAFETY TRANSMITTER (EASY 2S)

Land-line based security systems are the past. They are more expensive to operate and less secure than modern cellular-based security systems. No need to replace the whole system, only the signal transmitter module. Upgrade to cellular today.

The EASY2S is our reliable cellular alarm signal transmitter and remote input monitoring device for security systems. It is suitable for both alarm signaling, input monitoring (through its I/Os) and can even be used to control connected devices (like gates) remotely.

The communicator receives the incoming alarm signals from connected security sensors through the tip-ring plug and transmits alarm signals to the security monitoring or dispatch center through Contact ID (CID) or SIA DC-09 protocol. The device can be configured remotely using our EasyTerm config tool, or via SMS messages.

Notification can be made:

GSM network to a remote monitoring center
On a mobile internet network (LTE or 2G) to an IP address
To an IP receiver or SIMS Cloud server

It emits periodic life signals and provides detection and notification capabilities of wire cut sabotage. The output line can be switched remotely (for gate opening, device control).

Alarms or events can be configured to send immediate SMS notification (up to 4 phone numbers). The device can be ordered with 2G cellular module.

Benefits

Retrofit your land-line security system with our cellular alarm transmitter so you will not need to replace the whole system to have a future-proof solution
Use it as backup alarm transmission channel (GSM voice or data)
Connect external devices you would like to control remotely
Extend the system with further I/Os (due the optional expansion PCB)
Connect an extra siren, a spare battery pack, or a sabotage switch to the device and provide thus the highest level of safety for your home, office, company

Communication

Supporting LTE/2G cellular networks
GSM voice (for traditional dispatch centers)

Connectors

PCB version with fixation lags (for easy fit to housing, optional safety metal box)
2pcs isolated digital inputs (operation mode selection by jumpers)
- voltage (high level: 5-24V, low level: 0-1V)
- contact (0.3-1mA)
- detection of wire cut, short sabotage
1pc relay output (remote switch: 2A-120VAC, 1A-24VDC)
Simulated analog phone line (ALARM TIP-RING) input for alarm centers
Power/battery connector (8-24VDC, 800mA – terminal block)
micro-USB port (configuration, firmware refresh)
SMA-M antenna connector (50 Ohm)
Push insert-SIM card bay

Software features

Receiving alarm system signals
Event signaling with Contact ID (CID) or SIA DC-09 protocol, providing life signals
Wireless alarm signaling for dispatch center (analog GSM voice up to 4 phone lines)
Wireless alarm signaling for IP adresses (primary, backup server)
Handling zones, events
Voltage/contact input line change signaling (input line status changes)
Output switch/Gate control with delay (by local, SMS commands, by calling/ringing, TCP)
Massive contact list for output control
Advanced alarm SMS text notification (reports, IO status, alarms)
Voice call/ringing alarm notification (up to 4 phone numbers)
Without alarm center, it is also able to generate Contact ID codes (answer to input line signal changes)
Compatibility with SIA DTMF / SIA DC-09 protocol, IP receivers, SIMS Cloud^® software

Configuration

EasyTerm^® parameter configuration software (Windows^® is supported)
- Configuration (serial port, SMS text commands, TCP/IP
- Firmware refresh/configuration download/upload (serial port, Ftp)
- Remote access (TCP)
Operation status LEDs

Security

Watchdog (monitoring and auto recovery)
Configuration settings locally stored
Backup/spare battery connection
Siren connection (input line)
Wire cut, short circuit and sabotage detection

Accessories

RS232-USB cable (for configuration, updates) – optional
Communication antenna (gained, SMA) – according to module selection
Battery pack, battery charger, power supply – optional
Safety box (optional by order)
EasyTerm^® configuration software

Technical data

Product Datasheet

Quick Guide

Installation Guide

Firmware V21/R09/E05

EasyTerm 1.3.5 Configuration software (with factory configuration file)

Driver – FTDI driver for EasyTerm direct USB connection (Win XP/Vista/Win7/Win8/Win10/Win11)